Tips For Repairing Pipe Leaks On Your Own

Repairing Pipe Leaks On Your Own

Leaking pipes, no matter how big or small it is can create extreme changes on your water bills, negative changes to be specific. However, fixing minor leaks is actually easy and is something that you can manage to do without calling a plumber. Here are some ways on how you can repair pipe leaks by yourself.

Repairing Pipe Leaks On Your Own – Money Saving Tips

1.Fixing Leaks Through Tape

This is considered to be the easiest and cheapest way that anyone can do to fix small pipe leaks. All the material you would need is an electrical or duct tape. The basic principle here is that you should cover the leak using the tape. To effectively stop the leak, you should start wrapping the tape before the leak itself on your water pipe. Wrap in a diagonal manner around the pipe until you have covered the entire leaking area and a small portion extending before and after it.

2.Fixing Leaks By Epoxy

This method is best used if your leaking problem is situated at pipe fittings and joints. You can get epoxy from your local hardware store. First off, you
should cut off the water supply. Then you need to drain all the water from the pipes. Water purging can be done by letting the faucet run, until no more water comes out.

After purging the water, dry out the pipes and clean it using steel wool. Make sure that the pipes are dry and clean, since applying epoxy on a wet pipe can give unpleasant results. If you are sure, then apply the epoxy and let it dry. Refer to the epoxy’s packaging on how long you should let it stand to dry up. Avoid using the pipe line if the epoxy is still wet.

3.Fix Leaks Through A Pipe Clamp

You can use pipe clamp to fix your leaks. However, you should buy a clamp that has the right size to fit your leaking pipe. Once you have purchased a clamp, clean out your pipe. Be careful in cleaning it, and make sure that you do this well. Wrap your pipe in a rubber pad which should be placed over the area where the leak is. When you have the pad in place, put the pipe clamp over it and screw the clamp securely. If you have somewhat moderate leaks, you can also use this method to stop them.

4.Fixing Leaks Through Hose Clamps

Using a host clamp is kind of similar to using a pipe clamp. However, this is to be only used on smaller leaks. You can start by wrapping the pipe with a rubber pad. Once the pad is placed over the leaking area, put one or two hose clamps over it and tighten the pad by securely screwing it.

5.Fixing Leaks Through C-Clamps and Blocks

If your pipe is of a small size, then you can make use of a small sized c-clamp to patch it. Start by placing a rubber pad directly on top of the leak. After that, put a small wooden strip or block on top of it. Get the c-clamp and place it over the fixture to hold everything on place. You use the blocks as protection for the pipe from the pressure given by the c-clamp.

6.Fixing Leaks Using Tin Can Clamps

Here, what you would need is a tin can. Start off by cutting the ends off the can and cutting it up one side. Get the half of the can and bend its ends so that they are flat and could meet. This is like a homemade pipe clamp.

Get a rubber pad and place it over your leak. Above the rubber pad, place your homemade clamp. A c-clamp and wooden blocks can also be used to tighten the fixture.

Comments

  1. J D Winter says

    This is a very informative post indeed. I’m going to have to say that using epoxy, while being the most laborious method, is also the most secure and reliable by far.
    • says

      Hi J D
      Yes you are better off doing it properly so you don not have to do it again and again. When my husband and I were young we always tried to get away with cheap fixes but they never worked 🙂 Epoxy would last for ages and do a good job!
  2. Anne Lyken-Garner says

    This is a very detailed article on repairing leaks. I actually have an article like this on my site too. Different approaches, obviously, but I think they can both be effective when doing plumbing jobs.

    I’m not sure about the home made tin clamps, though. Have you tried them?

    • says

      I am pretty handy with the ideas but not at the jobs… So no I haven’t tried them… I like to make do with what ever I have though..Sometimes it works and other times it is a disaster!
  3. Daniel Smith says

    Hi Mikelle,
    There are very few articles on the internet which are as informative as this on how to stop pipe leaks on your own. Many of these ideas can be applied to any home as every household has access to tapes, rubber pads, pipe clamps and used tin cans. However, I totally agree with J D Winter that though it takes some efforts and time using epoxy, it is the most reliable and long lasting method.

Leave a Reply

Your email address will not be published. Required fields are marked *